STANDARD EXECUTION

• Two cylinder operation
• Large punch table with multi-purpose bolster, removable table block for overhang channel / joist flange punching
• Heavy duty punch table with guides and backstop
• Heavy duty support tables with guides at shear station and notch station
• Large throat depth at the punching station, extra deep throat models available
• Extensive range of applications: large hole punching crimping, tube notching, bar bending, sheet bending, punch press applications,...
• Punch adaptors
• Swing away punch stripper unit
• Easy change punch holder
• Universal die bolster
• 39" touch and cut backstop
• Non-tiltable and as thus wear-free angle-cutting blades
• Low-power inching and adjustable stroke at punch and shear end
• Mitre cut flanges of angle under shear blade
• Alternative rectangular / vee notching facility
• Work station guards standard fitment
• Overload relief on hydraulic system
• Centralized pressure lubrication
• Instruction, operating and maintenance manual
• Service tool kit
• Hydraulic oil included

PUNCHING

The large punch bed area - which has a removable front block is designed to give a very wide range of punching applications. A punch table with rules for repetition work is fitted as standard equipment.

In the overhang position flanges of channel or beam can be punched up to a diameter/diagonal of 1-1/2 inches maximum capacity.

Additional tooling in this versatile work station can provide bending, corner notching and general die-set work.

SECTION CUTTING

The machines are fitted as standard with blades for cutting round and square bars. With extra equipment, the machines are able to cut, in this aperture, Channels, Joists and Tee sections. The blades are retained by simple clamps, allowing easy changes without the need for elaborate setting.

ANGLE CUTTING

This station provides large capacity angle cutting at 90° and 45°. Angles between 45° and 90° can be achieved by first cutting at 90° and then flange trimming to the required angle in the shearing station. The hold-down supports the material thus ensuring a true cut.

SHEARING

The shearing unit is fitted with a simple robust hold-down which is adjustable to any thickness of material within the cutting capacity of the machine. A shear feed table with adjustable guides is fitted to allow the accurate feeding of materials. The guide can be adjusted to allow mitre cutting up to 45° for flat bars or to trim the flanges of angle sections previously cut at the angle cutting station.

The standard shear blades as fitted have a special raked cutting edge to give a clean cut with minimum distortion from full capacity down to as light as 1/8" thickness.

FEATURES

• Large punch table with multipurpose bolster - removable table block for overhang channel/joist flange punching.
• Punch table, shear table and notch table standard equipment.
• Power Inching and adjustable strokes at punch and shear end.
• Centralized pressure lubrication.
• Wide applications - for large hole punching, tube notching, bending.
• Punching - large throat depth (deeper throat models available).
• Low voltage movable light standard equipment.
• Mitre cut flanges of angle under shear blade.
• Alternative rectangular/vee notching facility.
• Work Station guards standard fitment.
• Two cylinder operation.
• Overload relief on hydraulic system.
• Interchangeable bearings, seals and valves readily available from stock lists of hydraulic equipment.
• Machines with low maintenance requirement.
• Kingsland machines are British made.

STANDARD EQUIPMENT SUPPLIED WITH MACHINE

Punch and Die, Easy Change Punch Holder, Ring, Adaptors, Swing Away Punch Stripper Unit, Universal Bolster for the punching of flats, angle and flanges of channel and joist. Repetition support tables at Punch, Shear, and Notch. Blades for cropping angle, cropping round and square bar, and for shearing flat bar. Rectangular notch unit. Service Tool Kit. Full tank hydraulic fluid. Work Station guards. Low voltage movable light.

CAPACITIES OF THE FIVE STATIONS (Short Tons/Inch)

Based on material strength of 62,000 PSI